RD F405 V3 Flight Controller & 50A–65A 4-in-1 ESC Stack (3-6S / 30.5x30.5mm)

RD F405 V3 Flight Controller & 50A–65A 4-in-1 ESC Stack (3-6S / 30.5x30.5mm)

RD F405 V3 Flight Controller Only
$23.66
Sale price  $23.66 Regular price  $23.66
Skip to product information
RD F405 V3 Flight Controller & 50A–65A 4-in-1 ESC Stack (3-6S / 30.5x30.5mm)

RD F405 V3 Flight Controller & 50A–65A 4-in-1 ESC Stack (3-6S / 30.5x30.5mm)

$23.66
Sale price  $23.66 Regular price  $23.66
Color

The RD F405 V3 Flight Controller and BLHeli_S 4-in-1 ESC Stack delivers a reliable, high-performance power and control foundation for 5-inch to 7-inch freestyle and long-range FPV drones. Powered by an STM32F405 processing core with Betaflight OSD integration, this stack features dual filtered BEC outputs (5V/2A and 9V/2A) to provide clean, isolated power to analog video transmitters, HD digital FPV air units, and flight camera systems.

Specifications

Parameter Flight Controller (RD F405 V3) 4-in-1 ESC (50A / 55A / 60A / 65A)
MCU STM32F405 High-speed EFM8BB21 / BLHeli_S
Input Voltage 3–6S LiPo (11.1V – 25.2V) 3–6S LiPo (11.1V – 25.2V)
Continuous / Burst Current N/A 50A, 55A, 60A, or 65A / Burst +5A–10A (10s)
Firmware Target Betaflight (F405 Target) BLHeli_S (Supports DShot300 / DShot600)
BEC Output 5V/2A, 9V/2A No BEC (Opto isolated signal interface)
Onboard OSD AT7456E (Analog Betaflight OSD) N/A
Mounting Pattern 30.5 × 30.5mm (M4 with M3 silicone grommets) 30.5 × 30.5mm (M4 with M3 silicone grommets)
Current Sensor Supported (scale calibration in Betaflight) Integrated current shunt resistor (Current pad output)

Before you buy

  • Five variants: FC only, and stacks with 50A / 55A / 60A / 65A ESCs. The FC alone cannot fly anything.
  • 3–6S only for both the FC and the ESC — 8S is out of spec.
  • The ESC is OPTO (no BEC) — the 5V/2A and 9V/2A rails come from the FC, so power your receiver and VTX from the FC, not the ESC.
  • AT7456E analog OSD — this is not a digital HD build unless you add a separate air unit.
  • 30.5 × 30.5 mm with M4 holes and M3 grommets — check screw length through the stack.

In the box

Package contents depend on the selected variant (Standalone FC or Complete Stack):

  • 1 × RD F405 V3 Flight Controller (or 1 × RD F405 V3 + Selected 4-in-1 ESC Stack)
  • 1 × 8-Pin SH1.0 ESC-to-FC Interconnect Wiring Harness
  • 4 × Silicone Anti-Vibration Damping Grommets (M3)
  • 1 × Low ESR Electrolytic Filter Capacitor (Stack combos only)
  • 1 × XT60 Power Pigtail Cable (Stack combos only)

Why this spec

  • STM32F405 Processing Core: High-speed processing power for responsive flight handling and fast loop rates.
  • Dual Filtered BEC Outputs: Dedicated 5V and 9V power rails ensure clean video feeds and dependable power for HD digital systems.
  • Versatile BLHeli_S ESC Options: Available with 50A, 55A, 60A, or 65A continuous current ratings to match varied motor stator sizes and propeller loads.
  • Vibration-Damped Mounting: Standard 30.5 × 30.5mm mounting pattern fitted with silicone grommets to isolate gyro sensors from motor resonance.
  • Comprehensive Peripherals: Solder pads for camera control, programmable LED strips, active buzzer, RSSI, and multiple hardware UARTs.

What you still need to complete the build

  • 4× motors and a 4-in-1 ESC
  • Receiver (ELRS/CRSF)
  • VTX and camera
  • GPS for rescue mode

Support and returns

Covered against manufacturing defects for 12 months. If a board arrives dead, loses a UART or will not hold a flash, contact us with the order number and a short video of the fault. Reverse-polarity damage, solder bridges and crash damage are not covered.

Frequently Asked Questions

How do I choose the correct version?

Available selections for this listing: RD F405 V3 Flight Controller Only; F405 FC + 50A ESC Stack; F405 FC + 55A ESC Stack; F405 FC + 60A ESC Stack; F405 FC + 65A ESC Stack. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.

Does every option include both a flight controller and an ESC?

No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.

How do I check the supported battery voltage?

Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.

Are matching-looking connectors plug-and-play?

Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.

Which firmware target should I use?

Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.

Is the current rating a guarantee for my installation?

No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.

How should I perform initial setup?

Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.

You may also like