F405 & FT722 Flight Controller / 60A–100A 4-in-1 ESC Series (2-8S / 30.5x30.5mm)
The F405 and FT722 Flight Controller and Heavy-Duty 4-in-1 ESC Series offers robust, high-voltage power distribution and precise flight stabilization for 5-inch freestyle drones through 10-inch commercial and cinematic UAV platforms. Featuring STM32F405 or high-speed FT722 flight controller options paired with 60A (2–6S), 80A (3–8S), or 100A (3–8S) BLHeli_S 4-in-1 ESCs, this hardware series delivers the thermal dissipation, current throughput, and filtering needed for demanding multi-rotor applications.
Specifications
| Component / Variant | Input Voltage | Continuous / Burst Current | Processor / Firmware | Key Features |
|---|---|---|---|---|
| 60A 4-in-1 ESC | 2–6S LiPo | 60A / 70A (10s) | BLHeli_S (DShot600) | Standard 30.5x30.5mm, Current Shunt Resistor |
| 80A 4-in-1 ESC | 3–8S LiPo | 80A / 90A (10s) | BLHeli_S (DShot600) | High-voltage MOSFETs, Onboard TVS Diode |
| 100A 4-in-1 ESC | 3–8S LiPo | 100A / 110A (10s) | BLHeli_S (DShot600) | Heavy copper power rails, Low ESR capacitors |
| F405 Flight Controller | 3–6S LiPo | N/A | STM32F405 / Betaflight | Dual BEC (5V/9V), AT7456E OSD, Type-C USB |
| FT722 Flight Controller | 3–6S LiPo | N/A | STM32F722 / Betaflight | 6 UARTs, ICM Gyro, SPL06 Barometer, 16MB Blackbox |
Before you buy
- Six variants across two FCs and three ESCs — 60A is 2–6S, 80A and 100A are 3–8S. Mismatching the pack to the ESC variant is the most common mistake here.
- F405 vs FT722: the F722 gives you 6 UARTs, ICM gyro, SPL06 barometer and 16MB blackbox; the F405 is the cheaper baseline.
- BLHeli_S / DShot600 on all ESC variants — no BLHeli_32.
- 30.5 × 30.5 mm stack pattern across the range.
- Burst is only 10 seconds above continuous — do not tune to the burst number.
In the box
Package contents depend on the selected configuration (Standalone ESC or FC+ESC Stack Combo):
- 1 × Standalone 4-in-1 ESC (60A, 80A, or 100A) OR 1 × Flight Controller + ESC Stack Combo
- 1 × SH1.0 8-Pin Wiring Interconnect Cable (with stack combos and standalone ESCs)
- 4 × Silicone Anti-Vibration Grommets (M3)
- 1 × Low-ESR Filter Capacitor (with ESCs and stack combos)
- 1 × Power Cable with XT60 Connector (with ESCs and stack combos)
Why this spec
- Flexible Processor Options: Choose between proven STM32F405 and ultra-responsive FT722 flight controllers equipped with Betaflight OSD and dual BEC outputs.
- High-Voltage & High-Current ESC Ratings: Available with 60A (2–6S LiPo), 80A (3–8S LiPo), or 100A (3–8S LiPo) continuous current capacity per motor channel.
- Heavy Copper Multi-Layer PCB: Multi-layer copper design and low internal resistance MOSFETs provide efficient heat dissipation under sustained full-throttle bursts.
- Broad Digital & Analog Compatibility: Dedicated wiring interfaces for DJI O3, Walksnail, HDZero, analog VTX systems, GPS modules, and external compasses.
- Standard 30.5 × 30.5mm Layout: Universal mounting dimensions ensure seamless installation across standard FPV and cinematic drone frames.
What you still need to complete the build
- 4× motors and a 4-in-1 ESC
- Receiver (ELRS/CRSF)
- VTX and camera
- GPS for rescue mode
Support and returns
Covered against manufacturing defects for 12 months. If a board arrives dead, loses a UART or will not hold a flash, contact us with the order number and a short video of the fault. Reverse-polarity damage, solder bridges and crash damage are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: 60A Four-in-one ESC2-6S; F405+60A; FT722+60A; 80A Four-in-one ESC3-8S; F405+80A; FT722+80A; 100A Four-in-one ESC3-8S. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.