BrotherHobby Avenger 3115 V5 710KV/730KV/910KV Brushless FPV Motor
The BrotherHobby Avenger 3115 V5 is a high-power brushless motor designed for 8-inch to 10-inch long-range FPV drones, cinelifter platforms, and multi-rotor UAVs. Featuring aviation-grade 7075 aluminum alloy construction, a hollow titanium alloy shaft, and Japanese NMB bearings, it is engineered for consistent performance under heavy flight loads.
Specifications
| Configuration | 12N14P |
| Available KV Ratings | 710KV / 730KV / 790KV / 910KV |
| Rated Voltage | 6S LiPo |
| Stator Dimensions | 31mm x 15mm |
| Shaft & Prop Thread | Hollow titanium alloy shaft / M5 thread |
| Mounting Pattern | M3 (19mm x 19mm) |
| Wire Specification | 18AWG silicone wire, 250mm length |
| Recommended Propellers | 8-inch to 10-inch FPV & folding propellers |
Before you buy
- 6S only, 8–10-inch props — recommended propeller range is stated by the manufacturer, so do not fit 5-inch props to chase RPM.
- 710KV / 730KV / 790KV / 910KV: lower KV for 10-inch endurance, 910KV for 8-inch punch. Higher KV on the same prop pulls more current.
- 19 × 19 mm M3 mounting — verify your arm slots.
- Hollow titanium shaft with M5 thread saves weight; it is not a crash-tolerant part.
- 18AWG 250 mm leads — keep ESC extensions short and equal length.
In the box
- 1x BrotherHobby Avenger 3115 V5 Brushless Motor
- 4x M3 Mounting Screws
- 1x M5 Aluminum Flanged Lock Nut
Why this spec
- 7075 Aluminum Bell & Base: AL 7075 casing with hard-anodized surface finish for impact and scratch resistance.
- Titanium Alloy Hollow Shaft: Combines structural strength with reduced rotational inertia.
- Japanese NMB Bearings: Oversized NMB bearings for smooth throttle control and reliable operational life.
- 0.2mm Stator Laminations: Kawasaki silicon steel stator core paired with N52H curved arc neodymium magnets.
- High-Grade Enamelled Windings: Insulated copper wire winding engineered for efficient thermal management during high-demand flights.
What you still need to complete the build
- A frame with the matching motor hole pattern
- ESCs or a 4-in-1 sized for the prop and cell count
- Props matched to the KV
- Locking compound for the motor screws
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: 710KV; 730KV; 910KV; 790KV. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
How do I choose the correct KV?
Choose the exact KV using motor test data for your intended battery voltage and propeller. KV alone does not determine thrust, efficiency or suitability for a particular aircraft.
Will this motor fit my frame and propeller?
Compare mounting-hole spacing, screw thread and depth, shaft or hub dimensions and available clearance with your frame and propeller. Similar stator sizes do not guarantee identical mounting.
How should I size the ESC and battery?
Use measured current for the selected motor, voltage and propeller combination, then check ESC thermal limits, battery current capability and connector ratings. Do not treat peak test figures as continuous-use guarantees.
Are thrust figures valid for every version?
No. Thrust and current depend on the exact KV, voltage, propeller and test conditions. Use only data that matches the selected configuration.
What should I check before the first run?
Verify screw clearance from the windings, secure the motor and wiring, and check rotation with propellers removed. Stop if there is binding, unusual vibration or abnormal heating.