BrotherHobby Returner 85A 6-12S 32-Bit 4-in-1 ESC (XT V1)
The BrotherHobby Returner 85A XT V1 is a high-voltage, heavy-duty 4-in-1 electronic speed controller designed for 6S–12S heavy-lift, cinematic, and industrial multirotors. Built with an 8-layer 3oz copper PCB, four solder-mask windowed copper bus plates, plug-and-play MR60PW motor sockets, and dual integrated XT120 battery inputs.
Specifications
| Model Name | Returner 6-12S 32Bit 85A (4IN1) ESC XT V1 |
| Firmware | AM32 / 2.18 |
| Continuous Current | 85A × 4 channels (at up to 50.4V) |
| Peak Burst Current | 95A per channel (10 seconds) |
| Input Voltage | 6S–12S LiPo |
| Output Voltage | 6S–12S LiPo |
| BEC Output | 19V / 3A |
| TVS Protection | 4× High-Power TVS Diodes |
| Capacitor Array | 4× 1000μF / 63V Low-ESR Capacitors + 90× SMD Filter Capacitors |
| ESC Protocols | PWM, DShot300, DShot600, DShot1200 |
| Current Sensor (CUR) | Supported (Telemetry / Analog Output to FC) |
| ESC Telemetry (TEL) | Supported |
| Mounting Hole Pattern | 30.5 × 30.5 mm (M3) |
| Board Dimensions | 128mm × 100mm |
| Overall Dimensions | 128mm × 114mm × 32mm (including connectors and capacitors) |
| Total Weight | 220g |
| Motor Connectors | 4× MR60PW Integrated Sockets |
| Battery Connectors | 2× XT120(2+2)-M Connectors |
Before you buy
- 85 A × 4 channels at up to 50.4 V (12S). That is a heavy-lift ESC — most 5-inch builds have no use for it.
- AM32 firmware, not BLHeli_S or BLHeli_32. Bluejay is not applicable; configure through AM32 tools, and confirm your FC's ESC protocol support.
- 19 V / 3 A BEC is a high-voltage rail — check what you power from it before connecting a 5 V-only device.
- Burnt FETs from a stalled prop are not warranty. Size props to stay under 85 A continuous per channel.
- 30.5 × 30.5 mm M3 mounting, 128 × 100 mm board — verify frame clearance for the heatsink and capacitor array.
In the box
- 1 × BrotherHobby Returner 6-12S 85A 4-in-1 ESC XT V1
- 5 × M3×8mm Silicone Anti-Vibration Grommets
- 1 × SH 1.0mm 8-Pin Wiring Harness Cable
Why this spec
- High-voltage 6S–12S LiPo operating range (up to 50.4V)
- 8-layer PCB constructed with 3oz heavy copper and 4 solder-mask windowed copper bus plates for high continuous current capacity
- Four plug-and-play MR60PW motor connector sockets for direct motor lead connection
- Dual integrated XT120(2+2)-M battery input connectors
- Pre-installed onboard filtering array: 4× 1000μF/63V high-frequency low-ESR electrolytic capacitors plus 90 SMD filtering capacitors
- Four onboard high-power TVS transient voltage suppression diodes for inductive spike protection
- Supports AM32 32-bit firmware (v2.18) with web and desktop configurator support
- Integrated 19V / 3A BEC output
- Standard 30.5×30.5mm mounting pattern with vibration-damping silicone grommets
- G (GND): Ground (Power Negative)
- V (VCC): Battery Voltage Telemetry output to Flight Controller
- M1 – M4: Throttle signal inputs for Channels 1 through 4
- CUR: Current detection signal output to Flight Controller
- TEL: Serial telemetry data output
What you still need to complete the build
- A charger rated for your cell count
- A LiPo-safe charging bag
- The correct connector for your build
Support and returns
Covered against manufacturing defects for 12 months. Contact us with your order number and photos or a short video of the fault and we will repair or replace the item. Crash damage, water ingress and modification are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: Returner 6-12S 32Bit am32 85A(4IN1) ESC XT V1. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.