QX-MOTOR Multi-Rotor Brushless ESC Series (20A–160A) & Testing Accessories
The QX-MOTOR Multi-Rotor Brushless ESC Series provides electronic speed controllers engineered for multi-rotors, aerial cinematography platforms, industrial heavy-lift drones, and EDF fixed-wing models. Spanning lightweight 20A micro speed controllers up to 160A industrial high-voltage units, the series includes both built-in switchable BEC models and optocoupler-isolated (OPTO) high-voltage controllers, along with dedicated bench-testing modules.
Specifications
| Specification Field | QX120A (3-6S Standard / BEC) | QX120A (6-12S High Voltage / OPTO) |
|---|---|---|
| Input Voltage Range | 3S – 6S LiPo (11.1V – 22.2V) | 6S – 12S LiPo (22.2V – 44.4V nominal, up to 50.4V max) |
| Continuous Current | 120A | 120A |
| Burst Current | 140A (10 seconds) | 140A (10 seconds) |
| BEC Output | Switchable 5.0V / 6.0V / 7.4V @ 5A (hardware toggle switch) | None / OPTO (optocoupler signal isolation, requires external 5V receiver power) |
| Enclosure Dimensions | 82 × 36 × 25 mm | Heavy-duty finned CNC aluminum heatsink case |
| Input Wiring | 10AWG, 90 mm length | Heavy-gauge high-voltage silicone wire |
| Output Motor Leads | 12AWG, 103 mm length with Φ4.0 mm female banana plugs | High-current silicone motor leads |
| Signal Cable | 360 mm length with standard JR 3-pin connector | Optically isolated twisted signal cable |
| Primary Applications | High-power EDF jets, 550–700 class RC helicopters, high-speed fixed-wing | Commercial multi-rotors, agricultural spray drones, 12S heavy-lift UAVs |
Before you buy
| Model / Variant | Input Voltage | BEC Output | Form Factor & Dimensions |
|---|---|---|---|
| QX20A (2-3S) | 2S – 3S LiPo | 5V / 2A Linear BEC | Heat-shrink sleeve (55 × 19 × 10 mm) |
| QX20A (3-4S) | 3S – 4S LiPo | None (OPTO) | Heat-shrink sleeve |
| QX30A (2-3S) | 2S – 3S LiPo | Built-in BEC | Heat-shrink sleeve |
| QX40A (3-4S) | 3S – 4S LiPo | Built-in BEC | Heat-shrink sleeve |
| QX40A (2-6S) | 2S – 6S LiPo | None (OPTO) | Heat-shrink sleeve |
| QX50A (3-4S) | 3S – 4S LiPo | Built-in BEC | Heat-shrink sleeve |
| QX60A (2-6S) | 2S – 6S LiPo | Switchable 5V / 6V / 7.4V @ 5A BEC | Heat-shrink sleeve with aluminum cooling plate |
| QX80A (2-6S) | 2S – 6S LiPo | 5V / 5A UBEC | Heat-shrink sleeve with aluminum heatsink (80A-UBEC) |
| QX100A (2-6S) | 2S – 6S LiPo | 5.5V / 5A UBEC | Aluminum housing with cooling fins |
| QX120A (3-6S) | 3S – 6S LiPo | Switchable 5V / 6V / 7.4V @ 5A BEC | Finned aluminum housing (82 × 36 × 25 mm) |
| QX120A (6-12S) | 6S – 12S LiPo (HV) | None (OPTO Optocoupler Isolation) | High-voltage CNC aluminum finned heatsink enclosure |
| QX160A (6-14S) | 6S – 14S LiPo (HV) | None (OPTO Optocoupler Isolation) | Industrial CNC aluminum heatsink case (87.5 × 43 × 27.5 mm) |
| Red Throttle / STV2.0 Tester | 4.8V – 6.0V DC | N/A | 3-CH PWM Manual / Neutral / Auto Sweep Tester |
| Blue Throttle / CCPM Master | 4.8V – 6.0V DC | N/A | 3-CH Consistency Master Knob Tester |
| Conversion Module + Switch | DC 5.0V – 12.0V | N/A | Signal conversion module with stepless potentiometer speed switch |
| FPV Three-Way Video Switch | 5.0V – 12.0V DC | N/A | 3-Input to 1-Output PWM controlled video channel switcher |
In the box
- 1 × Selected QX-MOTOR ESC or testing accessory module according to variant choice
Why this spec
- Comprehensive Current Range: Available from compact 20A models up to 160A heavy-lift industrial speed controllers.
- Distinct Low-Voltage (BEC) & High-Voltage (OPTO) Architectures: Models from 20A to 120A (3-6S) provide integrated receiver power with switchable BEC outputs on high-output models; dedicated high-voltage units like the QX120A (6-12S) and QX160A (6-14S) feature optocoupler signal isolation to eliminate ground loop noise.
- Switchable BEC on Mid/High Power Units: The QX60A, QX80A, and QX120A (3-6S) feature built-in multi-voltage BEC outputs (5.0V / 6.0V / 7.4V @ 5A) selectable via an onboard hardware switch.
- Bench Testing Tools Available: Precision 3-channel servo/ESC testers and multi-camera FPV video switcher modules allow direct ground testing and setup without an active radio transmitter.
What you still need to complete the build
- A flight controller with the matching harness
- Motors within the ESC current rating
- A capacitor across the battery pads
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: QX20A Electronic speed controller(2-3S); QX20A Electronic speed controller(3-4S); QX30A Electronic speed controller(2-3S); QX40A Electronic speed controller(3-4S); QX40A Electronic speed controller(2-6S); QX50A Electronic speed controller(3-4S); QX60A Electronic speed controller(2-6S); QX80A Electronic speed controller(2-6S); QX100A Electronic speed controller(2-6S); QX120A Electronic speed controller(3-6S); QX120A Electronic speed controller(6-12S); QX160A Electronic speed controller(6-14S); Red throttle; Blue throttle; Conversion module+Stepless speed control switch; FPV Three-way video switch. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.