F405 V3 Flight Controller & 4-in-1 ESC Stack – 50A / 60A / 80A / 100A (2-6S)
F405 V3 + 4-in-1 ESC is a matched flight stack: STM32F405 controller on top, 4-in-1 ESC below. Buying them as a stack means the wiring harness and mounting pattern already line up.
Specifications
| Flight controller | STM32F405 |
| Input voltage | 2–6S |
| ESC options | 50A / 60A / 80A / 100A (4-in-1) |
| Firmware | Betaflight / INAV compatible |
| Mounting | 30.5×30.5 mm |
| ESC protocol | DShot600 |
| Variants | FC only / ESC only / matched stack |
Before you buy
- Match ESC current to your motors. Four 2806.5 motors on 7-inch pull roughly 35–40A each at full throttle — 60A is the minimum sensible choice.
- Stack variants are pre-matched. Mixing an FC-only and an ESC-only variant will not include the interconnect cable.
- No receiver included. Add an ELRS receiver separately.
- FC only — you already have an ESC.
- ESC only — replacing a burnt 4-in-1.
- Stack — new build; cheapest way to get both.
- 5-inch: 50A or 60A. 7-inch: 60A or 80A. Heavy lift: 100A.
In the box
- Flight controller or ESC as selected
- Wiring harness (stack variants only)
- Mounting hardware
Why this spec
- Sold as a matched stack, so the 8-pin harness between FC and ESC is already pinned correctly — the single most common cause of a dead build is a swapped harness.
- STM32F405 runs Betaflight/INAV at full loop rate with blackbox; the board has a barometer footprint and 5 UARTs for GPS, VTX control and RX.
- 4-in-1 ESC uses 32-bit AM32-class firmware with current limiting and motor-direction reversal from the configurator.
- Both boards use the 30.5×30.5 mm stack pattern and share a common ground, avoiding the ground-loop noise that shows up as gyro drift.
What you still need to complete the build
- 1× frame (30.5×30.5 stack)
- 4× motors
- RX
- VTX + antenna
- GPS (optional)
- 6S LiPo
We stock every line above — order them together and the parts are matched, not guessed.
Support and returns
Every unit is checked before dispatch. If a part arrives damaged or does not match the specification table above, contact us with your order number and a photo and we will replace it. Consumables (props, antennas) are covered for manufacturing defects, not crash damage.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: F405 V3 Flight Controller Only; 50A 4-in-1 ESC Only; 60A 4-in-1 ESC Only; 80A 4-in-1 ESC Only; F405 FC + 50A ESC Stack; F405 FC + 60A ESC Stack; F405 FC + 80A ESC Stack; F405 FC + 100A ESC Stack. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.