QX-MOTOR Airplane-32 100A 2-6S Brushless ESC (5.5V/5A UBEC)
The QX-MOTOR Airplane-32 100A is a high-performance brushless electronic speed controller engineered for fixed-wing aircraft, EDF ducted fan jets, scale gliders, and high-drain RC models. Featuring a 32-bit ARM processing architecture and a built-in 5.5V @ 5A switch-mode UBEC, it delivers linear throttle response, high commutation efficiency, and reliable onboard power delivery to flight electronics and standard servos.
Specifications
| Model | QX-MOTOR Airplane-32 100A |
| Input Voltage | 2S – 6S LiPo (7.4V – 22.2V) |
| Continuous Current | 100A |
| Burst Current | 120A (10 seconds) |
| UBEC Output | 5.5V @ 5A Switch-Mode |
| Enclosure Dimensions | 75 × 38.5 × 20 mm (outer envelope with mounting tabs: ~78 × 38.5 × 20 mm) |
| Mounting Hole Spacing | 69 mm (length pitch) × 32.7 mm (width pitch), Φ3.0 mm screw holes |
| Weight | 116 g (including cables and connectors) |
| Input Power Leads | 110 mm length |
| Motor Output Leads | 130 mm length with Φ4.0 mm female banana plugs |
| Throttle Signal Lead | 330 mm length with standard JR 3-pin connector |
| Applications | RC fixed-wing aircraft, EDF ducted fans, scale gliders, and high-current UAV propulsion systems |
Before you buy
- 2–6S only — this is a fixed-wing/EDF ESC, not a high-voltage multirotor part.
- 5.5 V / 5 A switch-mode UBEC is included, so it can power a receiver and servos directly; 5.5 V is above the 5.0 V some servos expect, check ratings.
- 100 A continuous, 120 A for 10 s — size the prop so the sustained figure is not exceeded.
- 116 g with leads and Φ4.0 mm banana plugs on the motor side — your motor must have matching connectors or you re-solder.
- 69 × 32.7 mm mounting pitch, Φ3.0 mm holes — check the firewall holes before ordering.
In the box
- 1 × QX-MOTOR Airplane-32 100A 2-6S Brushless ESC (5.5V/5A UBEC, pre-soldered Φ4.0 mm female banana sockets)
Why this spec
- 32-Bit ARM Processing Architecture: Delivers high-speed processing, smooth throttle linearity, rapid dynamic acceleration, and efficient motor commutation.
- Integrated 5.5V / 5A UBEC: Built-in switch-mode UBEC provides a constant 5.5V output at up to 5A continuous current to reliably power flight controllers, receivers, and servos without requiring an external receiver battery.
- Precision Aluminum Housing: Aluminum heatsink enclosure with integrated side mounting tabs ensures optimal thermal dissipation during sustained high-throttle operation.
- Comprehensive Hardware Protections: Safeguards against low-voltage battery cutoff, over-temperature thermal overload, throttle signal loss, and motor startup lockup.
- Pre-Terminated Motor Leads: Motor phase cables come equipped with pre-soldered Φ4.0 mm female gold banana connectors for quick, secure connection.
What you still need to complete the build
- A flight controller with the matching harness
- Motors within the ESC current rating
- A capacitor across the battery pads
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: QX100A Electronic speed controller / 2-6S. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.