caddx-farsight-fpv-camera-8x-zoom

Caddx Farsight FPV Camera – 1/2" 1500TVL Analog, 1–8× Motorized Zoom, 9–24V

Farsight
$119.77
Sale price  $119.77 Regular price  $119.77
Skip to product information
caddx-farsight-fpv-camera-8x-zoom

Caddx Farsight FPV Camera – 1/2" 1500TVL Analog, 1–8× Motorized Zoom, 9–24V

$119.77
Sale price  $119.77 Regular price  $119.77
ColorFarsight

Caddx Farsight is an analog FPV camera with a motorized 1–8× zoom — rare in the analog world, and the reason long-range pilots use it. You keep a wide 122.5° view for cruising, then zoom in on whatever you spotted without losing link quality or adding latency.

Zoom is driven over PWM from your flight controller, so you can map it to a switch or dial and snap back to 1× instantly. A 1/2" sensor and 1500TVL output give noticeably cleaner detail than a standard 1/3" micro camera.

Specifications

Model Caddx Farsight
Image sensor 1/2"
Horizontal resolution 1500 TVL
Focal length 2.2 mm
Field of view 122.5° (H) × 92.2° (V) × 155° (D)
Minimum illumination 0.01 Lux
Zoom 1–8×, PWM controlled from flight controller
Aspect ratio 4:3
Video output Analog CVBS
Input voltage 9–24 V DC
Power consumption < 2 W
Camera size 19 × 19 × 19.5 mm
AI box size 33.5 × 33.5 × 12.35 mm
Operating temperature -20 °C to +60 °C

Before you buy

  • Do not power directly from a 6S pack. A fully charged 6S pack is 25.2 V and this camera's ceiling is 24 V. Feed it from a 12 V pad on your flight controller or use a BEC.
  • Analog only. CVBS output — not compatible with digital HD systems such as DJI O3/O4 or Walksnail.
  • Two-part install. The camera and the AI box are separate units; plan mounting space for both.
  • Zoom needs a spare PWM channel. Allocate one channel on your flight controller or receiver.

In the box

  • 1 × Farsight camera
  • 1 × AI box
  • 1 × connecting cable

Why this spec

  • Motorised 1–8× zoom on an analog camera: keep the 122.5° view for cruising, then zoom to identify without swapping lenses or adding a second camera.
  • Zoom is driven by PWM from the flight controller, so it maps to a dial or a three-position switch and snaps back to 1× instantly.
  • A 1/2" sensor is roughly 2.25× the area of the 1/3" sensor used in most micro cameras — that is where the extra detail at 1500 TVL comes from.
  • 9–24 V input runs from a 12 V pad on 4S–6S builds without a separate regulator.
  • Under 2 W draw leaves the whole power budget to the VTX, which matters on a 3 W long-range setup.

What you still need to complete the build

  • A VTX with a compatible video standard
  • 5V or variable supply within the camera's range
  • A mount matching the camera width

Support and returns

Covered against manufacturing defects for 12 months. If the zoom motor stalls, the image drops out or a unit arrives dead, contact us with the order number and a short video of the fault. Crash damage, reversed polarity and running it above 24 V are not covered.

Frequently Asked Questions

How do I choose the correct version?

Available selections for this listing: Farsight. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.

How do I choose the correct KV?

Choose the exact KV using motor test data for your intended battery voltage and propeller. KV alone does not determine thrust, efficiency or suitability for a particular aircraft.

Will this motor fit my frame and propeller?

Compare mounting-hole spacing, screw thread and depth, shaft or hub dimensions and available clearance with your frame and propeller. Similar stator sizes do not guarantee identical mounting.

How should I size the ESC and battery?

Use measured current for the selected motor, voltage and propeller combination, then check ESC thermal limits, battery current capability and connector ratings. Do not treat peak test figures as continuous-use guarantees.

Are thrust figures valid for every version?

No. Thrust and current depend on the exact KV, voltage, propeller and test conditions. Use only data that matches the selected configuration.

What should I check before the first run?

Verify screw clearance from the windings, secure the motor and wiring, and check rotation with propellers removed. Stop if there is binding, unusual vibration or abnormal heating.

You may also like