BrotherHobby SE 3115 900KV Brushless Motor
The BrotherHobby SE 3115 900KV is a high-output brushless motor developed for 6S heavy-payload and long-range multirotors swinging 8- to 10-inch propellers. It features Kawasaki/Nippon Steel 1500 stator laminations, N52H neodymium magnets, and pre-soldered 16AWG high-strand silicone wire leads.
Specifications
| KV Rating | 900KV |
| Configuration | 12N14P |
| Stator Dimensions | 31mm (Diameter) × 15mm (Height) |
| Motor Dimensions | Φ37.5mm × 46.75mm |
| Motor Weight | 125.20g (including 300mm wire) |
| Lead Wire | 16AWG Silicone Wire, 300mm length |
| Magnets | N52H |
| Phase Resistance | 42.0 mΩ |
| Idle Current (Io @ 10V) | 1.68A |
| Rated Operating Voltage | 6S LiPo |
| Recommended ESC | 6S 65A |
| Recommended Propeller | HQ 9×5×3 Glass Fiber Nylon |
| Max Continuous Current | 64.90A |
| Max Continuous Power | 1,596.54W |
| Insulation Resistance | ≥ 0.5 MΩ |
| Dynamic Balance Standard | ≤ 3mg |
| Base Mounting Pattern | 19×19mm (4× M3 on 19mm circle) |
| Propeller Shaft Thread | M5 |
Before you buy
- 900KV, 6S, 9-inch props — the manufacturer's own test data is on HQ 9×5×3, with 64.9 A max continuous and ~1597 W. That current figure is what the ESC must survive.
- Recommended ESC is 6S 65A per motor — a 45 A ESC will not hold this motor at full throttle.
- 125 g with 300 mm 16AWG wire — heavier than a 2806.5, so plan a 7–9-inch build.
- Phase resistance 42 mΩ and idle current 1.68 A at 10 V — efficiency data you can use to compare against alternatives.
- 19 × 19 mm M3 mounting, M5 prop thread.
In the box
- 1 × BrotherHobby SE 3115 900KV Brushless Motor
- 4 × M3×8mm Mounting Screws
- 1 × M5 Flange Propeller Nut
Why this spec
- 12N14P configuration with 31×15mm stator geometry
- Kawasaki/Nippon Steel 1500 ultra-thin silicon steel laminations
- High-temperature N52H neodymium curved magnets
- Pre-soldered 16AWG flexible silicone wire leads (300mm length)
- Dynamic balancing rated to ≤ 3mg for vibration-reduced performance
- Standard 19×19mm M3 mounting pattern with M5 propeller adapter shaft
Measured on manufacturer test platform with HQ 9×5×3 propeller on 6S LiPo. Internal copper temperature measured after 2 minutes at 100% throttle (26°C ambient).
| Throttle (%) | Voltage (V) | Current (A) | RPM | Thrust (gf) | Input Power (W) | Efficiency (gf/W) |
|---|---|---|---|---|---|---|
| 30% | 25.20V | 1.80A | 4,616 | 265 gf | 45.36W | 5.84 gf/W |
| 40% | 25.20V | 7.50A | 7,781 | 835 gf | 189.00W | 4.42 gf/W |
| 50% | 25.20V | 13.20A | 9,697 | 1,321 gf | 332.64W | 3.97 gf/W |
| 60% | 25.10V | 23.90A | 11,748 | 1,987 gf | 599.89W | 3.31 gf/W |
| 70% | 25.00V | 40.50A | 13,645 | 2,838 gf | 1,012.50W | 2.80 gf/W |
| 80% | 24.80V | 52.00A | 14,632 | 3,249 gf | 1,289.60W | 2.52 gf/W |
| 90% | 24.80V | 61.70A | 15,412 | 3,656 gf | 1,530.16W | 2.39 gf/W |
| 100% | 24.60V | 64.90A | 15,569 | 3,784 gf | 1,596.54W | 2.37 gf/W |
Peak Temperature: 81°C internal copper temperature after 2 minutes at 100% throttle.
What you still need to complete the build
- A frame with the matching motor hole pattern
- ESCs or a 4-in-1 sized for the prop and cell count
- Props matched to the KV
- Locking compound for the motor screws
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: 900KV. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
How do I choose the correct KV?
Choose the exact KV using motor test data for your intended battery voltage and propeller. KV alone does not determine thrust, efficiency or suitability for a particular aircraft.
Will this motor fit my frame and propeller?
Compare mounting-hole spacing, screw thread and depth, shaft or hub dimensions and available clearance with your frame and propeller. Similar stator sizes do not guarantee identical mounting.
How should I size the ESC and battery?
Use measured current for the selected motor, voltage and propeller combination, then check ESC thermal limits, battery current capability and connector ratings. Do not treat peak test figures as continuous-use guarantees.
Are thrust figures valid for every version?
No. Thrust and current depend on the exact KV, voltage, propeller and test conditions. Use only data that matches the selected configuration.
What should I check before the first run?
Verify screw clearance from the windings, secure the motor and wiring, and check rotation with propellers removed. Stop if there is binding, unusual vibration or abnormal heating.