BrotherHobby Avenger 3008 Brushless Motor

BrotherHobby Avenger 3008 Brushless Motor

1150KV
$25.76
Sale price  $25.76 Regular price  $25.76
Skip to product information
BrotherHobby Avenger 3008 Brushless Motor

BrotherHobby Avenger 3008 Brushless Motor

$25.76
Sale price  $25.76 Regular price  $25.76
Size

The BrotherHobby Avenger 3008 is a wide-stator brushless motor engineered for 6- to 8-inch long-range, cinematic, and endurance multirotors. Built with a 12N14P configuration, 7075 aluminum bell housing, titanium alloy hollow shaft, and N52H curved neodymium magnets.

Specifications

Stator Size 3008 (30mm diameter × 8mm height)
Configuration 12N14P
Bell & Base Material 7075 Aluminum Alloy
Shaft Material Titanium Alloy Hollow Shaft
Propeller Shaft Thread M5
Magnets N52H Curved Neodymium
Motor Dimensions Φ35.3mm × 37.7mm (16mm shaft length, 8.5mm thread)
Lead Wire 18AWG Silicone Wire, 250mm length
Base Mounting Pattern 19×19mm (4× M3 on 19mm circle)
Available KV Options 1150KV, 1300KV, 1500KV, 1900KV

Before you buy

  • 3008 is a 7-inch long-range stator. 1150KV and 1300KV are 6S on 7-inch, 1500KV is 6S on 6-inch, 1900KV is 4S territory — do not put 1900KV on a 7-inch prop at 6S.
  • Titanium hollow shaft with M5 thread saves weight but is not a crash part: a hard prop strike can bend it.
  • 12N14P with N52H magnets — this is the standard high-torque layout, so expect good part-throttle efficiency and a punchy top end.
  • 18AWG silicone leads are short by design; you will extend them to the ESC. Keep the extension short and equal length on all four.
  • Check the frame's motor mount slots for 19 × 19 mm M3 before ordering.

In the box

  • 1 × BrotherHobby Avenger 3008 Brushless Motor
  • 4 × M3 Mounting Screws
  • 2 × M5 Propeller Nuts (Standard Flange Nut + Low-Profile Nut)

Why this spec

  • 7075 aluminum alloy bell and base with wear-resistant hard-anodized surface finish
  • N52H curved neodymium magnets designed for uniform magnetic flux distribution
  • High-tensile titanium alloy hollow shaft with standard M5 propeller thread
  • 0.2mm silicon steel stator laminations for minimized iron losses
  • Pre-installed 18AWG silicone lead wires (250mm length)
  • Standard 19×19mm M3 base mounting pattern

Factory bench tests conducted on manufacturer test stands (26°C ambient). Values are indicative and vary with atmospheric pressure, battery discharge rate, and ESC timing.

KV Variant Tested Propeller ESC & Voltage Throttle Current RPM Thrust Power Efficiency Copper Temp (2 min)
1300KV Gemfan 7035 Tri-Blade 6S 45A (24.0V / 23.8V) 50%
100%
9.6A
42.4A
13,868
22,512
725 gf
2,347 gf
230.4W
1,009.1W
3.15 gf/W
2.33 gf/W
--
105.7°C
1900KV HQ 6×3.5×3 4S 65A (16.8V) 50%
100%
13.9A
50.1A
13,847
21,201
885 gf
2,095 gf
233.5W
841.7W
3.79 gf/W
2.49 gf/W
--
45.0°C

What you still need to complete the build

  • A frame with the matching motor hole pattern
  • ESCs or a 4-in-1 sized for the prop and cell count
  • Props matched to the KV
  • Locking compound for the motor screws

Support and returns

Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.

Frequently Asked Questions

How do I choose the correct version?

Available selections for this listing: 1150KV; 1300KV; 1500KV; 1900KV. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.

How do I choose the correct KV?

Choose the exact KV using motor test data for your intended battery voltage and propeller. KV alone does not determine thrust, efficiency or suitability for a particular aircraft.

Will this motor fit my frame and propeller?

Compare mounting-hole spacing, screw thread and depth, shaft or hub dimensions and available clearance with your frame and propeller. Similar stator sizes do not guarantee identical mounting.

How should I size the ESC and battery?

Use measured current for the selected motor, voltage and propeller combination, then check ESC thermal limits, battery current capability and connector ratings. Do not treat peak test figures as continuous-use guarantees.

Are thrust figures valid for every version?

No. Thrust and current depend on the exact KV, voltage, propeller and test conditions. Use only data that matches the selected configuration.

What should I check before the first run?

Verify screw clearance from the windings, secure the motor and wiring, and check rotation with propellers removed. Stop if there is binding, unusual vibration or abnormal heating.

You may also like