TBS Lucid H7 Flight Controller (STM32H743 / Dual Gyro)
The TBS Lucid H7 is a high-performance flagship flight controller developed by Team BlackSheep for high-speed FPV racing, long-range missions, and professional cinematography platforms. Powered by a lightning-fast 480MHz STM32H743 processor and backed by dual ICM42688 gyroscopes, it delivers responsive filtering, extensive UART connectivity, and complete multi-platform firmware compatibility including Betaflight, ArduPilot, and INAV.
Specifications
| MCU | STM32H743VIH6 @ 480MHz (1MB RAM, 2MB Flash) |
| Gyroscope | Dual ICM42688 (ICM42688 × 2) |
| Barometer | Infineon DPS310 (I2C2) |
| OSD | AT7456E (SPI2) & Digital HD OSD Support |
| Blackbox | MicroSD Card Slot (SDIO) |
| UART Ports | 7 Ports (UART 1, 2, 3, 4, 6, 7, 8) with Hardware Inversion |
| Bus Interfaces | 2 × I2C, 1 × CAN Bus, 1 × SPI3 |
| Input Voltage | 9V – 36V (3S – 8S LiPo) |
| BEC Outputs | 5V @ 2A (Max 3A) / 9V @ 2A (Max 3A) / 3.3V LDO @ 200mA |
| USB Interface | Type-C (USB 2.0) |
| Firmware Targets | Betaflight, ArduPilot, INAV |
Before you buy
- H7 at 480 MHz with 1 MB RAM means you can run 8 kHz PID loop and still log to SD — but only if you keep the loop time sane; pushing 8k/8k on a 7-inch build usually costs more than it gains.
- 3S–8S input (9–36 V). The onboard regulator takes 8S, so no external BEC is needed for the FC itself.
- Dual ICM42688 gyros are not automatic redundancy. You still have to configure which gyro the firmware uses; the second one is a spare, not a hot standby on stock firmware.
- 7 UARTs with hardware inversion — that is enough for ELRS, GPS, VTX control and DJI HD at once, but plan the map before soldering; the pads are small.
- MicroSD via SDIO is fast enough for full-rate blackbox. Use a card rated for continuous write, not a random spare.
In the box
- 1 × TBS Lucid H7 Flight Controller
- 1 × JST-SH1.0 8-Pin Wiring Harness
- 1 × JST-GH1.25 4-Pin CAN Cable
- 1 × Anti-Vibration Silicone Damping Grommet Set
Why this spec
- 480MHz STM32H743 Architecture: Ultra-fast ARM processor with 1MB RAM and 2MB Flash easily runs high PID loop frequencies and complex autonomous navigation algorithms.
- Dual ICM42688 Gyros: Dual sensor arrangement reduces acoustic vibration sensitivity and delivers clean gyro filtering in challenging frame installations.
- High-Precision Barometer & Blackbox: Equipped with an Infineon DPS310 barometer and an SDIO MicroSD card slot for high-rate blackbox flight data logging.
- Extensive Peripheral I/O: Features 7 hardware-inversion UART ports, 2 I2C buses, a dedicated CAN bus, and 13 PWM outputs.
- Dual Camera Switching: Integrated hardware video switch allows in-flight switching between two FPV cameras.
- Wide Input Voltage & Dual BEC: Operates directly on 3S to 8S LiPo (9V – 36V) with filtered 5V 2A/3A and 9V 2A/3A BEC outputs for clean VTX and camera power.
What you still need to complete the build
- Check the specification table for the parts this item pairs with
Support and returns
Covered against manufacturing defects for 12 months. If a board arrives dead, loses a UART or will not hold a flash, contact us with the order number and a short video of the fault. Reverse-polarity damage, solder bridges and crash damage are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: Black Sheep TBS LUCID H7Flight Control A-TBSS-LDFH7 / H7. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.